Improving through-thickness conductivity of carbon fiber reinforced polymer using carbon nanotube/polyethylenimine at the interlaminar region

The through-thickness conductivity of carbon fiber reinforced polymer (CFRP) composite was increased by incorporating multiwalled carbon nanotubes in the interlaminar region. Carbon nanotubes (CNTs) were dispersed in a polyethylenimine (PEI) binder, which was then coated onto the carbon fiber fabric. Standard vacuum-assisted resin infusion process was applied to fabricate the composite laminates. This modification technique aims to enhance the electrical conductivity in through-thickness direction for the purpose of nondestructive testing, damage detection, and electromagnetic interference shielding. CNT concentrations ranging from 0 to 0.75 wt% were used and compared to pristine CFRP samples (reference). The through-thickness conductivity of the CFRP exhibited an improvement of up to 781% by adopting this technique. However, the dispersion of CNT in PEI led to a viscosity increase and poor wetting properties which resulted in the formation of voids/defects, poor adhesion (as shown in scanning electron micrographs) and the deterioration of the mechanical properties as manifested by interlaminar shear strength and dynamic mechanical analysis measurements.     

Low-Fired Electrotechnical Porcelain with Diopside Additives

Glass and Ceramics - The effect of diopside on the sintering temperature, structure, and properties of low-temperature electrotechnical porcelain was investigated. Diopside concentrate in the...     

Calculating the Process of Loose Material Mixing

Chemical and Petroleum Engineering - On the basis of scientific provisions of statistical mechanics and the entropy method arising from these provisions, the article substantiates the physical and...     

Segmental Baffles as a Means of Improving the Heat Transfer Efficiency of Air Coolers

Chemical and Petroleum Engineering - A comparative analysis of the main types of air coolers (ACs) is presented. Their advantages and disadvantages are indicated along with the main approaches for...     

Evaluation of the Range of Stable and Efficient Operation of Column Mass Transfer Devices with Jet-Film Contact Devices

Chemical and Petroleum Engineering - A contact device for heat and mass transfer devices with the ability to maintain the uniformity of flow distribution over the cross section of the device is...     

Study of the Transformation of Gallium Arsenide Surface Layers under the Action of Light by Means of Surface Acoustic Waves

Journal of Communications Technology and Electronics - Changes in the state of the surface layer of semi-insulating (111) GaAs in air under the action of white light are studied using surface...     

Development of a difunctional oxirane and multifunctional acrylate interpenetrating polymer network composite system with antimicrobial properties

This research continued the development of a difunctional Oxirane and multifunctional Acrylate interpenetrating polymer network composite System (OASys) with antimicrobial properties. The effects of 4-Isopropyl-4′-methyldiphenyliodonium tetrakis (pentafluorophenyl) borate (Borate), hexamethylene diamine (HMDA) and N,N-dimethyl p-toluidine (DMPT) on OASys (Epalloy 5001:dipentaerythritol hexaacrylate) composite hardness, contact angle, monomer-to-polymer degree of conversion (DoC), mechanical properties, polymerization shrinkage, shrinkage stress, and antimicrobial properties were determined. Bis-GMA:TEGDMA composites were used as the control. OASys composites with 9 wt% Borate and 0.5 wt% DMPT or 1.5 wt% HMDA had comparable hardness, DoC's and polymerization shrinkages to controls, but had lower contact angles and mechanical properties. Additionally, OASys composites with 1.5 wt% HMDA had significantly less polymerization stress than controls and demonstrated significant antibacterial activity against Streptococcus mutans and Lactobacillus casei out to 3 months. With lower shrinkage stress and long-term antimicrobial activity, OASys composites look promising for increasing the clinical lifetime of dental composites, but improvements in mechanical properties are needed.     

The Current State of Analysis,Synthesis, and Optimal Functioning of Multiproduct Digital Chemical Plants: Analytical Review

Theoretical Foundations of Chemical Engineering - An analytical review of the state of multiproduct chemical plants has been proposed. A comprehensive analysis is made of works of Russian and...     

3D CaP porous scaffolds with grooved surface topography obtained by the sol-gel method

The influence of surface topography on cellular behaviour and its importance for the development of three-dimensional scaffolds for bone tissue engineering are a topic of growing interest. To date, the introduction of topographical patterns into the surface of 3D porous ceramic scaffolds has proven difficult, due partly to the brittle nature of ceramic materials as well as the currently available fabrication technologies. In this study, a grooved pattern was introduced into the surface of 3D multilayer porous ceramic scaffolds by the chemical etching technique. The patterned scaffolds were characterised by X-Ray Diffraction (XRD), Scanning Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (SEM-EDX) and Digital Holographic Microscopy (DHM). Their bioactivity was also evaluated in vitro by immersion in simulated body fluid (SBF) for 12 h, 1, 7, 14 and 21 days. Scaffolds were constituted mainly with a mixture of the calcium pyrophosphate (Ca₂O₇P₂) and β-tricalcium phosphate (Ca?(PO?)?) phases. The pyrophosphate on the external layer was dissolved as a result of the etching process, leaving grooves on the surface. Ridges and grooves were nano-/micrometric, with dimensions of around 900 nm–1.5 μm in width and 200 nm–300 nm in depth. Moreover, the mechanical properties and bioactive capacity of the patterned scaffolds were not affected by chemical etching, making them suitable to be used in bone tissue engineering.     

Thermohydrodynamic Processes in Spray Drying with Convective–Radiation Energy Supply

Theoretical Foundations of Chemical Engineering - The results of numerical modeling of the heat and mass transfer of drops during drying of a liquid under the conditions of...